Codebergdnkl

foot

master
ply5 git calls26 ms34 KiB3 cachedprotocol v2
825 lines19 KiBRaw
1foot-ctlseqs(7)
3# NAME
4foot-ctlseqs - terminal control sequences supported by foot
6# DESCRIPTION
8This document describes all the control sequences supported by foot.
10- Control characters
11- Sequences beginning with ESC
12- CSI - Control Sequence Introducer
13 - SGR
14 - Indexed and RGB colors (256-color palette and 24-bit colors)
15 - Private modes
16 - Window manipulation
17 - Other
18- OSC - Operating System Command
19- DCS - Device Control String
21# Control characters
23[[ *Sequence*
24:[ *Name*
25:< *Description*
26| \\a
27: BEL
28: Depends on what *bell* in *foot.ini*(5) is set to.
29| \\b
30: BS
31: Backspace; move the cursor left one step. Wrap if _bw_ is enabled.
32| \\t
33: HT
34: Horizontal tab; move the cursor to the next tab stop.
35| \\n
36: LF
37: Line feed; move the cursor down one step, or scroll content up if
38 at the bottom line.
39| \\v
40: VT
41: Vertical tab; identical to _LF_.
42| \\f
43: FF
44: Form feed; identical to _LF_.
45| \\r
46: CR
47: Carriage ret; move the cursor to the leftmost column.
48| \\x0E
49: SO
50: Shift out; select the _G1_ character set.
51| \\x0F
52: SI
53: Shift in; select the _G0_ character set.
55# Sequences beginning with ESC
57Note: this table excludes sequences where ESC is part of a 7-bit
58equivalent to 8-bit C1 controls.
60[[ *Sequence*
61:[ *Name*
62:[ *Origin*
63:< *Description*
64| \\E 7
65: DECSC
66: VT100
67: Save cursor position.
68| \\E 8
69: DECRC
70: VT100
71: Restore cursor position.
72| \\E c
73: RIS
74: VT100
75: Reset terminal to initial state.
76| \\E D
77: IND
78: VT100
79: Line feed; move the cursor down one step, or scroll content up if
80 at the bottom margin.
81| \\E E
82: NEL
83: VT100
84: Next line; move the cursor down one step, and to the first
85 column. Content is scrolled up if at the bottom line.
86| \\E H
87: HTS
88: VT100
89: Set one horizontal tab stop at the current position.
90| \\E M
91: RI
92: VT100
93: Reverse index; move the cursor up one step, or scroll content down
94 if at the top margin.
95| \\E N
96: SS2
97: VT220
98: Single shift select of G2 character set (affects next character only).
99| \\E O
100: SS3
101: VT220
102: Single shift select of G3 character set (affects next character only).
103| \\E =
104: DECKPAM
105: VT100
106: Switch keypad to _application_ mode.
107| \\E >
108: DECKPNM
109: VT100
110: Switch keypad to _numeric_ mode.
111| \\E ( _C_
112: SCS
113: VT100
114: Designate G0 character set. Supported values for _C_ are: *0* (DEC
115 Special Character and Line Drawing Set), and *B* (USASCII).
116| \\E ) _C_
117: SCS
118: VT100
119: Designate G1 character set. Same supported values for _C_ as in _G0_.
120| \\E \* _C_
121: SCS
122: VT220
123: Designate G2 character set. Same supported values for _C_ as in _G0_.
124| \\E + _C_
125: SCS
126: VT220
127: Designate G3 character set. Same supported values for _C_ as in _G0_.
129# CSI
131All sequences begin with *\\E[*, sometimes abbreviated "CSI". Spaces
132are used in the sequence strings to make them easier to read, but are
133not actually part of the string (i.e. *\\E[ 1 m* is really *\\E[1m*).
135## SGR
137All SGR sequences are in the form *\\E[* _N_ *m*, where _N_ is a decimal
138number - the _parameter_. Multiple parameters can be combined in a
139single CSI sequence by separating them with semicolons: *\\E[ 1;2;3
140m*.
142[[ *Parameter*
143:< *Description*
144| 0
145: Reset all attributes
146| 1
147: Bold
148| 2
149: Dim
150| 3
151: Italic
152| 4
153: Underline, including styled underlines
154| 5
155: Blink
156| 7
157: Reverse video; swap foreground and background colors
158| 8
159: Conceal; text is not visible, but is copiable
160| 9
161: Crossed-out/strike
162| 21
163: Double underline
164| 22
165: Disable *bold* and *dim*
166| 23
167: Disable italic
168| 24
169: Disable underline
170| 25
171: Disable blink
172| 27
173: Disable reverse video
174| 28
175: Disable conceal
176| 29
177: Disable crossed-out
178| 30-37
179: Select foreground color (using *regularN* in *foot.ini*(5))
180| 38
181: Select foreground color, see "indexed and RGB colors" below
182| 39
183: Use the default foreground color (*foreground* in *foot.ini*(5))
184| 40-47
185: Select background color (using *regularN* in *foot.ini*(5))
186| 48
187: Select background color, see "indexed and RGB colors" below
188| 49
189: Use the default background color (*background* in *foot.ini*(5))
190| 58
191: Select underline color, see "indexed and RGB colors" below
192| 59
193: Use the default underline color
194| 90-97
195: Select foreground color (using *brightN* in *foot.ini*(5))
196| 100-107
197: Select background color (using *brightN* in *foot.ini*(5))
199## Indexed and RGB colors (256-color palette and 24-bit colors)
201Foot supports both the new sub-parameter based variants, and the older
202parameter based variants for setting foreground and background colors.
204Indexed colors:
206- *\\E[ 38 : 5 :* _idx_ *m*
207- *\\E[ 38 ; 5 ;* _idx_ *m*
209RGB colors:
211- *\\E[ 38 : 2 :* _cs_ *:* _r_ *:* _g_ *:* _b_ *m*
212- *\\E[ 38 : 2 :* _r_ *:* _g_ *:* _b_ *m*
213- *\\E[ 38 ; 2 ;* _r_ *;* _g_ *;* _b_ *m*
215The first variant is the "correct" one (and foot also recognizes, but
216ignores, the optional _tolerance_ parameters).
218The second one is allowed since many programs "forget" the color space
219ID, _cs_.
221The sub-parameter based variants are preferred, and are what foot's
222*terminfo*(5) entry uses.
224## Private Modes
226There are several Boolean-like "modes" that affect certain aspects
227of the terminal's behavior. These modes can be manipulated with the
228following 4 escape sequences:
230[[ *Sequence*
231:[ *Name*
232:< *Description*
233| \\E[ ? _Pm_ h
234: DECSET
235: Enable private mode
236| \\E[ ? _Pm_ l
237: DECRST
238: Disable private mode
239| \\E[ ? _Pm_ s
240: XTSAVE
241: Save private mode
242| \\E[ ? _Pm_ r
243: XTRESTORE
244: Restore private mode
247The _Pm_ parameter in the above sequences denotes a numerical ID
248that corresponds to one of the following modes:
250[[ *Parameter*
251:[ *Origin*
252:< *Description*
253| 1
254: VT100
255: Cursor keys mode (DECCKM)
256| 5
257: VT100
258: Reverse video (DECSCNM)
259| 6
260: VT100
261: Origin mode (DECOM)
262| 7
263: VT100
264: Auto-wrap mode (DECAWM)
265| 12
266: AT&T 610
267: Cursor blink
268| 25
269: VT220
270: Cursor visibility (DECTCEM)
271| 45
272: xterm
273: Reverse-wraparound mode
274| 47
275: xterm
276: Same as 1047 (see below)
277| 66
278: VT320
279: Numeric keypad mode (DECNKM); same as DECKPAM/DECKPNM when enabled/disabled
280| 1000
281: xterm
282: Send mouse x/y on button press/release
283| 1001
284: xterm
285: Use hilite mouse tracking
286| 1002
287: xterm
288: Use cell motion mouse tracking
289| 1003
290: xterm
291: Use all motion mouse tracking
292| 1004
293: xterm
294: Send FocusIn/FocusOut events
295| 1006
296: xterm
297: SGR mouse mode
298| 1007
299: xterm
300: Alternate scroll mode
301| 1015
302: urxvt
303: urxvt mouse mode
304| 1016
305: xterm
306: SGR-Pixels mouse mode
307| 1034
308: xterm
309: 8-bit Meta mode
310| 1035
311: xterm
312: Num Lock modifier (see xterm numLock option)
313| 1036
314: xterm
315: Send ESC when Meta modifies a key (see xterm metaSendsEscape option)
316| 1042
317: xterm
318: Perform action for BEL character (see *bell* in *foot.ini*(5))
319| 1047
320: xterm
321: Use alternate screen buffer
322| 1048
323: xterm
324: Save/restore cursor (DECSET=save, DECRST=restore)
325| 1049
326: xterm
327: Equivalent to 1048 and 1047 combined
328| 1070
329: xterm
330: Use private color registers for each sixel
331| 2004
332: xterm
333: Wrap pasted text with start/end delimiters (bracketed paste mode)
334| 2026
335: terminal-wg
336: Application synchronized updates mode
337| 2027
338: contour
339: Grapheme cluster processing
340| 2031
341: contour
342: Request color theme updates
343| 2033
344: rockorager
345: Request terminal visibility reports. Enabling this mode immediately reports
346 the current visibility as *CSI ? 999 ; 1|2 n*, where *1* means potentially
347 visible and *2* means not visible. Further reports are sent whenever the
348 visibility changes.
349| 2048
350: TODO
351: In-band window resize notifications
352| 8452
353: xterm
354: Position cursor to the right of sixels, instead of on the next line
355| 737769
356: foot
357: Input Method Editor (IME) mode
359## Window manipulation
361Foot implements a sub-set of XTerm's (originally dtterm's) window
362manipulation sequences. The generic format is:
364*\\E[ *_Ps_* ; *_Ps_* ; *_Ps_* t*
366[[ *Parameter 1*
367:[ *Parameter 2*
368:< *Description*
369| 11
370: -
371: Report if window is iconified. Foot always reports *1* - not iconified.
372| 13
373: -
374: Report window position. Foot always reports (0,0), due to Wayland
375 limitations.
376| 13
377: 2
378: Report text area position. Foot always reports (0,0) due to Wayland
379 limitations.
380| 14
381: -
382: Report text area size, in pixels. Foot reports the grid size,
383 excluding the margins.
384| 14
385: 2
386: Report window size, in pixels. Foot reports the grid size plus the
387 margins.
388| 15
389: -
390: Report the screen size, in pixels.
391| 16
392: -
393: Report the cell size, in pixels.
394| 18
395: -
396: Report text area size, in characters.
397| 19
398: -
399: Report screen size, in characters.
400| 20
401: -
402: Report icon label.
403| 22
404: -
405: Push window title+icon.
406| 22
407: 1
408: Push window icon.
409| 22
410: 2
411: Push window title.
412| 23
413: -
414: Pop window title+icon.
415| 23
416: 1
417: Pop window icon.
418| 23
419: 2
420: Pop window title.
422## Other
424[[ *Parameter*
425:[ *Name*
426:[ *Origin*
427:< *Description*
428| \\E[ _Ps_ c
429: DA
430: VT100
431: Send primary device attributes. Foot responds with "I'm a VT220 with
432 sixel and ANSI color support".
433| \\E[ _Ps_ A
434: CUU
435: VT100
436: Cursor up - move cursor up _Ps_ times.
437| \\E[ _Ps_ B
438: CUD
439: VT100
440: Cursor down - move cursor down _Ps_ times.
441| \\E[ _Ps_ C
442: CUF
443: VT100
444: Cursor forward - move cursor to the right _Ps_ times.
445| \\E[ _Ps_ D
446: CUB
447: VT100
448: Cursor backward - move cursor to the left _Ps_ times.
449| \\E[ _Ps_ g
450: TBC
451: VT100
452: Tab clear. _Ps_=0 -> clear current column. _Ps_=3 -> clear all.
453| \\E[ _Ps_ ; _Ps_ f
454: HVP
455: VT100
456: Horizontal and vertical position - move cursor to _row_ ; _column_.
457| \\E[ _Ps_ ; _Ps_ H
458: CUP
459: VT100
460: Cursor position - move cursor to _row_ ; _column_.
461| \\E[ _Ps_ J
462: ED
463: VT100
464: Erase in display. _Ps_=0 -> below cursor. _Ps_=1 -> above
465| \\E[ _Ps_ K
466: EL
467: VT100
468: Erase in line. _Ps_=0 -> right of cursor. _Ps_=1 -> left of
469 cursor. _Ps_=2 -> all.
470| \\E[ _Pm_ h
471: SM
472: VT100
473: Set mode. _Pm_=4 -> enable IRM (Insertion Replacement Mode). All
474 other values of _Pm_ are unsupported.
475| \\E[ _Pm_ l
476: RM
477: VT100
478: Reset mode. _Pm_=4 -> disable IRM (Insertion Replacement Mode). All
479 other values of _Pm_ are unsupported.
480| \\E[ _Ps_ n
481: DSR
482: VT100
483: Device status report. _Ps_=5 -> device status. _Ps_=6 -> cursor
484 position.
485| \\E[ _Ps_ L
486: IL
487: VT220
488: Insert _Ps_ lines.
489| \\E[ _Ps_ M
490: DL
491: VT220
492: Delete _Ps_ lines.
493| \\E[ _Ps_ P
494: DCH
495: VT220
496: Delete _Ps_ characters.
497| \\E[ _Ps_ @
498: ICH
499: VT220
500: Insert _Ps_ blank characters.
501| \\E[ _Ps_ X
502: ECH
503: VT220
504: Erase _Ps_ characters.
505| \\E[ > c
506: DA2
507: VT220
508: Send secondary device attributes. Foot responds with "I'm a VT220
509 and here's my version number".
510| \\E[ ! p
511: DECSTR
512: VT220
513: Soft terminal reset.
514| \\E[ ? _Ps_ $ p
515: DECRQM
516: VT320
517: Request status of DEC private mode. The _Ps_ parameter corresponds
518 to one of the values mentioned in the "Private Modes" section above
519 (as set with DECSET/DECRST).
520| \\E[ _Ps_ $ p
521: DECRQM
522: VT320
523: Request status of ECMA-48/ANSI mode. See the descriptions for SM/RM
524 above for recognized _Ps_ values.
525| \\E[ _Pt_ ; _Pl_ ; _Pb_ ; _Pr_ ; _Pm_ $ r
526: DECCARA
527: VT400
528: Change attributes in rectangular area. _Pt_, _Pl_, _Pb_ and _Pr_
529 denotes the rectangle, _Pm_ denotes the SGR attributes.
530| \\E[ _Pt_ ; _Pl_ ; _Pb_ ; _Pr_ ; _Pm_ $ t
531: DECRARA
532: VT400
533: Invert attributes in rectangular area. _Pt_, _Pl_, _Pb_ and _Pr_
534 denotes the rectangle, _Pm_ denotes the SGR attributes.
535| \\E[ _Pt_ ; _Pl_ ; _Pb_ ; _Pr_ ; _Pp_ ; _Pt_ ; _Pl_ ; _Pp_ $ v
536: DECCRA
537: VT400
538: Copy rectangular area. _Pt_, _Pl_, _Pb_ and _Pr_ denotes the
539 rectangle, _Pt_ and _Pl_ denotes the target location.
540| \\E[ _Pc_ ; _Pt_ ; _Pl_ ; _Pb_ ; _Pr_ $ x
541: DECFRA
542: VT420
543: Fill rectangular area. _Pc_ is the character to use, _Pt_, _Pl_,
544 _Pb_ and _Pr_ denotes the rectangle.
545| \\E[ _Pt_ ; _Pl_ ; _Pb_ ; _Pr_ $ z
546: DECERA
547: VT400
548: Erase rectangular area. _Pt_, _Pl_, _Pb_ and _Pr_ denotes the
549 rectangle.
550| \\E[ _Ps_ T
551: SD
552: VT420
553: Scroll down _Ps_ lines.
554| \\E[ s
555: SCOSC
556: SCO, VT510
557: Save cursor position.
558| \\E[ u
559: SCORC
560: SCO, VT510
561: Restore cursor position.
562| \\E[ _Ps_ SP q
563: DECSCUSR
564: VT510
565: Set cursor style. In foot, _Ps_=0 means "use style from foot.ini".
566| \\E[ = _Ps_ c
567: DA3
568: VT510
569: Send tertiary device attributes. Foot responds with "FOOT", in
570 hexadecimal.
571| \\E[ _Pm_ d
572: VPA
573: ECMA-48
574: Line position absolute - move cursor to line _Pm_.
575| \\E[ _Pm_ e
576: VPR
577: ECMA-48
578: Line position relative - move cursor down _Pm_ lines.
579| \\E[ _Pm_ a
580: HPR
581: ECMA-48
582: Character position relative - move cursor to the right _Pm_ times.
583| \\E[ _Ps_ E
584: CNL
585: ECMA-48
586: Cursor next line - move the cursor down _Ps_ times.
587| \\E[ _Ps_ F
588: CPL
589: ECMA-48
590: Cursor preceding line - move the cursor up _Ps_ times.
591| \\E[ _Pm_ `
592: HPA
593: ECMA-48
594: Character position absolute - move cursor to column _Pm_.
595| \\E[ _Ps_ G
596: CHA
597: ECMA-48
598: Cursor character absolute - move cursor to column _Ps_.
599 cursor. _Ps_=2 -> all. _Ps_=3 -> saved lines.
600| \\E[ _Ps_ S
601: SU
602: ECMA-48
603: Scroll up _Ps_ lines.
604| \\E[ _Ps_ I
605: CHT
606: ECMA-48
607: Cursor forward tabulation _Ps_ tab stops.
608| \\E[ _Ps_ Z
609: CBT
610: ECMA-48
611: Cursor backward tabulation _Ps_ tab stops.
612| \\E[ _Ps_ b
613: REP
614: ECMA-48
615: Repeat the preceding printable character _Ps_ times.
616| \\E[ ? _Pi_ ; _Pa_ ; _Pv_ S
617: XTSMGRAPHICS
618: xterm
619: Set or request sixel attributes.
620| \\E[ > _Ps_ q
621: XTVERSION
622: xterm
623: _Ps_=0 -> report terminal name and version, in the form
624 *\\EP>|foot(version)\\E\\*.
625| \\E[ > 4 ; _Pv_ m
626: XTMODKEYS
627: xterm
628: Set level of the _modifyOtherKeys_ property to _Pv_. Note that foot
629 only supports level 1 and 2, where level 1 is the default setting.
630| \\E[ ? _Pp_ m
631: XTQMODKEYS
632: xterm
633: Query key modifier options
634| \\E[ > 4 n
635: <unnamed>
636: xterm
637: Resets the _modifyOtherKeys_ property to level 1. Note that in foot,
638 this sequence does not completely disable _modifyOtherKeys_, since
639 foot only supports level 1 and level 2 (and not level 0).
640| \\E[ ? u
641: <unnamed>
642: kitty
643: Query current values of the Kitty keyboard flags.
644| \\E[ > _flags_ u
645: <unnamed>
646: kitty
647: Push a new entry, _flags_, to the Kitty keyboard stack.
648| \\E[ < _number_ u
649: <unnamed>
650: kitty
651: Pop _number_ of entries from the Kitty keyboard stack.
652| \\E[ = _flags_ ; _mode_ u
653: <unnamed>
654: kitty
655: Update current Kitty keyboard flags, according to _mode_.
656| \\E[ # P
657: XTPUSHCOLORS
658: xterm
659: Push current color palette onto stack
660| \\E[ # Q
661: XTPOPCOLORS
662: xterm
663: Pop color palette from stack
664| \\E[ # R
665: XTREPORTCOLORS
666: xterm
667: Report the current entry on the palette stack, and the number of
668 palettes stored on the stack.
669| \\E[ ? 996 n
670: Query the current (color) theme mode
671: contour
672: The current color theme mode (light or dark) is reported as *CSI ?
673 997 ; 1|2 n*, where *1* means dark and *2* light. By convention, the
674 primary theme in foot is considered dark, and the alternative theme
675 light.
676| \\E[ ? 998 n
677: Query terminal visibility
678: rockorager
679: The current terminal visibility is reported as *CSI ? 999 ; 1|2 n*, where
680 *1* means potentially visible and *2* means not visible. This does not enable
681 private mode 2033.
684# OSC
686All _OSC_ sequences begin with *\\E]*, sometimes abbreviated _OSC_.
688[[ *Sequence*
689:[ *Origin*
690:< *Description*
691| \\E] 0 ; _Pt_ \\E\\
692: xterm
693: Set window icon and title to _Pt_.
694| \\E] 1 ; _Pt_ \\E\\
695: xterm
696: Set window icon to _Pt_.
697| \\E] 2 ; _Pt_ \\E\\
698: xterm
699: Set window title to _Pt_
700| \\E] 4 ; _c_ ; _spec_ \\E\\
701: xterm
702: Change color number _c_ to _spec_, where _spec_ is a color in
703 XParseColor format. foot only supports RGB colors; either
704 *rgb:<red>/<green>/<blue>*, or the legacy format (*#rgb*).
705| \\E] 7 ; _Uri_ \\E\\
706: iTerm2
707: Update the terminal's current working directory. Newly spawned
708 terminals will launch in this directory. _Uri_ must be in the format
709 *file://<hostname>/<path>*. *hostname* must refer to your local host.
710| \\E] 8 ; id=_ID_ ; _Uri_ \\E\\
711: VTE+iTerm2
712: Hyperlink (a.k.a HTML-like anchors). id=_ID_ is optional; if assigned,
713 all URIs with the same _ID_ will be treated as a single
714 hyperlink. An empty URI closes the hyperlink.
715| \\E] 9 ; _msg_ \\E\\
716: iTerm2
717: Desktop notification, uses *notify* in *foot.ini*(5).
718| \\E] 10 ; _spec_ \\E\\
719: xterm
720: Change the default foreground color to _spec_, a color in
721 XParseColor format.
722| \\E] 11 ; _spec_ \\E\\
723: xterm
724: Change the default background color to _spec_, a color in
725 XParseColor format. Foot implements URxvt's transparency extension;
726 e.g. _spec_=*[75]#ff00ff* or _spec_=*rgba:ff/00/ff/bf* (pink with
727 75% alpha).
728| \\E] 12 ; _spec_ \\E\\
729: xterm
730: Change cursor color to _spec_, a color in XParseColor format.
731| \\E] 17 ; _spec_ \\E\\
732: xterm
733: Change selection background color to _spec_, a color in
734 XParseColor format.
735| \\E] 19 ; _spec_ \\E\\
736: xterm
737: Change selection foreground color to _spec_, a color in XParseColor
738 format.
739| \\E] 22 ; _xcursor-pointer-name_ \\E\\
740: xterm
741: Sets the xcursor pointer. An empty name, or an invalid name resets
742 it.
743| \\E] 52 ; _Pc_ ; ? \\E\\
744: xterm
745: Send clipboard data. _Pc_ can be either *c*, *s* or *p*. *c* uses
746 the clipboard as source, and *s* and *p* uses the primary
747 selection. The response is *\\E] 52 ; Pc ; <base64-encoded data>
748 \E\\*, where _Pc_ denotes the source used.
749| \\E] 52 ; _Pc_ ; _Pd_ \\E\\
750: xterm
751: Copy _Pd_ (base64 encoded text) to the clipboard. _Pc_ denotes the
752 target: *c* targets the clipboard and *s* and *p* the primary
753 selection.
754| \\E] 66 ; _params_ ; text \\E\\
755: kitty
756: Text sizing protocol (only 'w', width, supported)
757| \\E] 99 ; _params_ ; _payload_ \\E\\
758: kitty
759: Desktop notification; uses *desktop-notifications.command* in
760 *foot.ini*(5).
761| \\E] 104 ; _c_ \\E\\
762: xterm
763: Reset color number _c_ (multiple semicolon separated _c_ values may
764 be provided), or all colors (excluding the default
765 foreground/background colors) if _c_ is omitted.
766| \\E] 110 \\E\\
767: xterm
768: Reset default foreground color
769| \\E] 111 \\E\\
770: xterm
771: Reset default background color
772| \\E] 112 \\E\\
773: xterm
774: Reset cursor color
775| \\E] 117 \\E\\
776: xterm
777: Reset selection background color
778| \\E] 119 \\E\\
779: xterm
780: Reset selection foreground color
781| \\E] 133 ; A \\E\\
782: FinalTerm
783: Mark start of shell prompt
784| \\E] 133 ; C \\E\\
785: FinalTerm
786: Mark start of command output
787| \\E] 133 ; D \\E\\
788: FinalTerm
789: Mark end of command output
790| \\E] 176 ; _app-id_ \\E\\
791: foot
792: Set app ID. _app-id_ is optional; if assigned,
793 the terminal window App ID will be set to the value.
794 An empty App ID resets the value to the default.
795| \\E] 555 \\E\\
796: foot
797: Flash the entire terminal (foot extension)
798| \\E] 777;notify;_title_;_msg_ \\E\\
799: urxvt
800: Desktop notification, uses *desktop-notifications.command* in
801 *foot.ini*(5).
803# DCS
805All _DCS_ sequences begin with *\\EP* (sometimes abbreviated _DCS_),
806and are terminated by *\\E\\* (ST).
808[[ *Sequence*
809:< *Description*
810| \\EP q <sixel data> \\E\\
811: Emit a sixel image at the current cursor position
812| \\EP $ q <query> \\E\\
813: Request selection or setting (DECRQSS). Implemented queries:
814 DECSTBM, SGR and DECSCUSR.
815| \\EP = _C_ s \\E\\
816: Begin (_C_=*1*) or end (_C_=*2*) application synchronized updates.
817 This sequence is supported for compatibility reasons, but it's
818 recommended to use private mode 2026 (see above) instead.
819| \\EP + q <hex encoded capability name> \\E\\
820: Query builtin terminfo database (XTGETTCAP)
823# FOOTNOTE
825Foot does not support 8-bit control characters ("C1").
Diagnostics5 git calls · 26 ms
CallStatusSizeTime026 ms
discover200178 B3 ms
git.upload-pack discover
http.response.status_code=200
git.upstream.cf_ray=-
git.upstream.phase=fetch
git.upstream.dur_ms=2
git.response.bytes=178
git.server.agent=git/2.56.1-Linux
git.server.object_format=sha1
git.server.caps=agent ls-refs fetch server-option object-format
git.server.fetch=shallow wait-for-done filter
git.protocol.version=2
git.pkt.frames=9
git.pkt.data=7
git.pkt.flush=2
git.pkt.delim=0
git.pkt.bytes=178
git.pkt.payload.max=35
ls-refs20010 KiB3 ms
git.upload-pack ls-refs
http.response.status_code=200
git.upstream.cf_ray=-
git.upstream.phase=ls-refs
git.upstream.dur_ms=3
git.response.bytes=10322
git.response.cache=UPDATING
git.response.duration_ms=3
git.protocol.version=2
git.pkt.frames=108
git.pkt.data=107
git.pkt.flush=1
git.pkt.delim=0
git.pkt.bytes=10322
git.pkt.payload.max=106
git.ls_refs.count=107
git.ls_refs.head=refs/heads/master
fetchtree:0 · deepen 102009.3 KiB · hit2 ms
git.upload-pack fetch
http.response.status_code=200
git.upstream.cf_ray=-
git.upstream.phase=fetch
git.upstream.dur_ms=3
git.response.bytes=9489
git.response.cache=HIT
git.response.duration_ms=2
git.fetch.filter=tree:0
git.fetch.wants=c0d2c3e95d74cb60526ff28aec9f34ee3df545e0
git.fetch.haves.count=0
git.fetch.deepen=10
git.fetch.thin_pack=false
git.fetch.ofs_delta=true
git.protocol.version=2
git.pkt.frames=7
git.pkt.data=5
git.pkt.flush=1
git.pkt.delim=1
git.pkt.bytes=9489
git.pkt.payload.max=9389
git.sideband.band1.bytes=9389
git.sideband.band2.bytes=0
git.sideband.band3.bytes=0
git.pack.objects=10
git.pack.bytes=9389
git.pack.ofs_delta=0
git.pack.ref_delta=0
git.pack.chain.max=0
git.pack.trailer=de930681b6073ba5b599a0f956bfbd114762ad5a
git.pack.full=10
Open pack map
fetchcombine:blob:none+tree:2 · deepen 12008.6 KiB · hit3 ms
git.upload-pack fetch
http.response.status_code=200
git.upstream.cf_ray=-
git.upstream.phase=fetch
git.upstream.dur_ms=20
git.response.bytes=8830
git.response.cache=HIT
git.response.duration_ms=3
git.fetch.filter=combine:blob:none+tree:2
git.fetch.wants=c0d2c3e95d74cb60526ff28aec9f34ee3df545e0
git.fetch.haves.count=0
git.fetch.deepen=1
git.fetch.thin_pack=false
git.fetch.ofs_delta=true
git.protocol.version=2
git.pkt.frames=7
git.pkt.data=5
git.pkt.flush=1
git.pkt.delim=1
git.pkt.bytes=8830
git.pkt.payload.max=8730
git.sideband.band1.bytes=8730
git.sideband.band2.bytes=0
git.sideband.band3.bytes=0
git.pack.objects=14
git.pack.bytes=8730
git.fetch.wide.objects=14
git.fetch.wide.extra_bytes=9909
git.fetch.wide.blobs=0
fetch2006.3 KiB · hit20 ms
git.upload-pack fetch
http.response.status_code=200
git.response.bytes=6501
git.response.cache=HIT
git.response.duration_ms=20
git.fetch.wants=192628cd58e88e68aa417efdde4751e4ef5a4944
git.fetch.haves.count=0
git.fetch.deepen=0
git.fetch.thin_pack=false
git.fetch.ofs_delta=true
git.protocol.version=2
git.pkt.frames=4
git.pkt.data=3
git.pkt.flush=1
git.pkt.delim=0
git.pkt.bytes=6501
git.pkt.payload.max=6474
git.sideband.band1.bytes=6474
git.sideband.band2.bytes=0
git.sideband.band3.bytes=0

Each row is one HTTP round trip ply made to the git server for this page, on one timeline. discover asks what the server speaks, ls-refs lists branch tips, fetch brings objects by id. A hit was served by Workers Cache. Tap a row for its wire details.

Remote
https://codeberg.org/dnkl/foot
Ref
refs/heads/master
Commit
c0d2c3e95d74cb60526ff28aec9f34ee3df545e0
cf-ray
a5e2f00d6ef6fda9
Request
b39787f7…
Protocol
v2 · sha1
Agent
git/2.56.1-Linux
Filter
advertised
Fetch
shallow wait-for-done filter
Capabilities
agent ls-refs fetch server-option object-format